While a house fire may be one of the most preventable disasters to happen to a home, a wildfire can be one of the least preventable on a small scale. Prevention of wildfires requires that a large number of people do what they can to make sure that the wildfires that do start are not manmade, but this awareness is only just now starting to catch on. When the fire is creeping toward your home, you are not likely to care what caused it, only what you can do to slow it down and in fact, there are a few different things that you can do to minimize the damage.
You may enjoy living in a more rural area, but you are at a disadvantage when it comes to wildfires because this is where they begin. One of the bad things about living in a rural area is that fire departments are not as prevalent, so the response to your home may not be as quick as you need it to be.
If you are contemplating having a home built for you, have it made of fire-resistant materials. Houses with an exterior made of brick, stone, or even metal will resist catching on fire much more than those that have exteriors made of wood or vinyl siding.
The most important exterior surface of your home is the roof. This is the largest surface area on the exterior of your home and it should be made of fire-resistant materials instead of the traditional wooden or oil-based shingles. Everyone knows that oil catches on fire very easily, so if you live in an area that is prone to wildfires, you may want to have another roofing material put on your home. Something else to do with your roof if a wildfire is nearby is to wet it down with the garden hose. This will give a little extra protection against the firebrands that are being carried in the air by the wind. Wetting the exterior walls of the house and wood decks is also a very good idea.
Do not allow any dead vegetation to build up in the yard. This includes grass cuttings, sticks, dead plants, and leaves. If a wildfire starts before you have a chance to get these dead organic materials cleaned up, all you can do is soak them and the rest of the yard with water via the hose and hope for the best.
Trees should also not be located close to the house, especially if the branches hang over the roof.
Jim Gaykern is a writer and promoter of quality
Charlotte, NC Water Damage Restoration and other states and cities such as
Marlboro, NJ Water Damage Restoration companies across the united states.
Thursday, October 18, 2007
Dealing With Wet Front and Backyards
Standing water in the front or the back yard can be an eyesore for both the homeowner and other people in the neighborhood, but it is not typically something that cannot be remedied. Depending on the source of the problem, it can be solved usually by either installing a drainage system or by the addition of a bit of soil in the right areas.
Allowing standing water in your yard, especially around the foundation of your house, can be detrimental both to the value of the property and to the structural integrity of the home. Water collecting in pockets around the base of the house can seep down into the basement or cause the house to slowly sink into the ground due to soil displacement over time. Wet soil does not form a good foundation for a home, so you need to try and fix this problem as soon as you run across it.
Many times simply piling soil in the areas where the water collects will fix the problem, since it is usually a simple issue of elevation. Some areas of your yard may not be the same elevation as other parts and water collects in these spots. Putting soil in these and planting grass over them not only for a pleasing visual effect, but also to keep the soil well in place, is the only real way to deal with elevation issues.
Putting in a drainage system is also a good option and it is not that expensive to install. You need a shovel, some gravel, PVC pipe, and a sink strainer. You should not have to hire anyone to do this for you, since all it takes is a little common sense and a bit of effort. You do, however, need to make sure that you obtain a permit to install the drain system, depending on where you live. Some areas may require that you get a permit to install a drainage system in your yard and want you to ask permission before directing the water into a city sewer or ditch.
Dig the ditch starting at the part of the yard that you want to drain and dig it to the area you want the water to go to. This ditch should slant downhill so that the water does not simply stand inside the drain and go nowhere. To get an adequate amount of water flow, it should decline 6 inches for every 100 feet. Install the PVC pipe inside it and cover with gravel. Cover that with soil and plant grass over it. This should keep the water drained well, but if you need more than one spot in your yard drained, the construction may be a little more complicated.
Dror Klar is a writer and promoter of
Glen Cove, NY Wet Basement Drying
and
Orlando FL Water Removal Emergency Service Which are Certified IICRC Water damage and mold remediation contractors.
Allowing standing water in your yard, especially around the foundation of your house, can be detrimental both to the value of the property and to the structural integrity of the home. Water collecting in pockets around the base of the house can seep down into the basement or cause the house to slowly sink into the ground due to soil displacement over time. Wet soil does not form a good foundation for a home, so you need to try and fix this problem as soon as you run across it.
Many times simply piling soil in the areas where the water collects will fix the problem, since it is usually a simple issue of elevation. Some areas of your yard may not be the same elevation as other parts and water collects in these spots. Putting soil in these and planting grass over them not only for a pleasing visual effect, but also to keep the soil well in place, is the only real way to deal with elevation issues.
Putting in a drainage system is also a good option and it is not that expensive to install. You need a shovel, some gravel, PVC pipe, and a sink strainer. You should not have to hire anyone to do this for you, since all it takes is a little common sense and a bit of effort. You do, however, need to make sure that you obtain a permit to install the drain system, depending on where you live. Some areas may require that you get a permit to install a drainage system in your yard and want you to ask permission before directing the water into a city sewer or ditch.
Dig the ditch starting at the part of the yard that you want to drain and dig it to the area you want the water to go to. This ditch should slant downhill so that the water does not simply stand inside the drain and go nowhere. To get an adequate amount of water flow, it should decline 6 inches for every 100 feet. Install the PVC pipe inside it and cover with gravel. Cover that with soil and plant grass over it. This should keep the water drained well, but if you need more than one spot in your yard drained, the construction may be a little more complicated.
Dror Klar is a writer and promoter of
Glen Cove, NY Wet Basement Drying
and
Orlando FL Water Removal Emergency Service Which are Certified IICRC Water damage and mold remediation contractors.
How to Deal With Sewage Damage
There are only a few things that bring a more unpleasant image to the mind of a person than the idea of sewage and coming into contact with it. If the area where you live has been flooded recently, you may need to deal with that very thing as you are allowed to go back to your home after the waters have receded, since it is often the case that these very waters are contaminated with it, among other unpleasant items. Sewage, chemicals, decaying bodies, and other things may be lurking in the flood water that has overrun your home, so cleaning it out of the nooks and crannies of your home is going to be quite the task. If you are prepared, however, you can save a lot of money by doing most of the cleanup yourself.
Everything in the house needs to be taken outside, especially wet furniture. Unfortunately, your upholstered furniture will not be salvageable unless there is little padding, such as the upholstery on some dining chairs. Large items like couches and recliners will need to be thrown away 95% of the time because the padding will soak up sewage, soil, and chemicals, causing it to become a biological hazard. These items are very difficult to completely disinfect and you will waste much time and money trying to do so. Replacing them is your best bet.
Cloth items in the tops of closets that did not come into contact with the water can become molded simply because of the humidity in the house. This typically starts after about 3 or 4 days, since they were not actually soaked by the flood. Get these items out and wash them as soon as you can, but not in your home’s washer, since it was probably flooded, too. Do not use your household appliances until they have been checked for electrical damage. Take anything you need to wash to a Laundromat.
Mold can start growing on textiles and other materials within about 48 hours after they have gotten wet. You can save these items most of the time, but they may be stained. Cleaning molded items made of real leather, however, is not possible.
Scrubbing your floors can be done by taking a couple of buckets, one with cleaning water and the other with rinsing water, and being sure not to contaminate the clean water with sewage. Do not put the sponge or mop back into the clean water without rinsing it first. Replace the rinsing water as often as you need to.
Jim Gaykern is a writer and promoter of quality
flood water damage restoration Trenton, NJ and and other states and cities such as
Trumbull, CT Water Damage Restoration companies across the united states.
Everything in the house needs to be taken outside, especially wet furniture. Unfortunately, your upholstered furniture will not be salvageable unless there is little padding, such as the upholstery on some dining chairs. Large items like couches and recliners will need to be thrown away 95% of the time because the padding will soak up sewage, soil, and chemicals, causing it to become a biological hazard. These items are very difficult to completely disinfect and you will waste much time and money trying to do so. Replacing them is your best bet.
Cloth items in the tops of closets that did not come into contact with the water can become molded simply because of the humidity in the house. This typically starts after about 3 or 4 days, since they were not actually soaked by the flood. Get these items out and wash them as soon as you can, but not in your home’s washer, since it was probably flooded, too. Do not use your household appliances until they have been checked for electrical damage. Take anything you need to wash to a Laundromat.
Mold can start growing on textiles and other materials within about 48 hours after they have gotten wet. You can save these items most of the time, but they may be stained. Cleaning molded items made of real leather, however, is not possible.
Scrubbing your floors can be done by taking a couple of buckets, one with cleaning water and the other with rinsing water, and being sure not to contaminate the clean water with sewage. Do not put the sponge or mop back into the clean water without rinsing it first. Replace the rinsing water as often as you need to.
Jim Gaykern is a writer and promoter of quality
flood water damage restoration Trenton, NJ and and other states and cities such as
Trumbull, CT Water Damage Restoration companies across the united states.
How to Keep Your Basement Dry
Most homeowners do not consider the basement a very important part of the house, but since the rest of your home’s structure is on top of this, you might want to rethink just how valuable of a room this is. Whether you use it for storage, a guest bedroom, laundry room, or anything else you can think of, it is important to make sure that this room of the house remains structurally sound.
While it is a common problem, wet basements are something that most homeowners do not have to deal with if they take some precautions and the time to make some adjustments on their own. Many wet basement issues can be fixed by the homeowner without having to hire any outside help.
You can fix any cracks in the concrete walls of your basement where water is leaking in by using a simple injection of concrete. Doing this used to require expensive and heavy equipment, but the size and expense of this has gone down so significantly that you can now do it with a normal caulking gun. Do not try do this with the silicone caulking that you would use in a bathroom or kitchen or attempt to fix it with cement, either. These two items will only become loose and fall out, no longer forming the water barrier that you need to have in place.
If water is forming in puddles around the foundation of your house, then you probably need to pile some more soil around the house so the water runs away from the house instead of leaking down into the basement. Installing a drainage system can also help with this. Making sure your rain gutters stay cleaned out is also another thing that you can do to try and keep water out of your basement. While they seem unrelated, gutters that are clogged let water merely fall off the roof and down to the base of the house.
You can also choose to install a dehumidifier and some energy efficient windows. You will know that you have a humidity problem in the room if condensation builds up on the window panes. Putting in an exhaust vent down there can also help reduce the humidity, especially if you use the area as a laundry room or an extra bathroom. This helps prevent the steam from being absorbed by the rafters or the drywall ceiling.
Dror Klar is a writer and promoter of
Flushing, Kew Gardens, Maspeth Water Removal
and
Elizabeth NJ Wet Basement Flooding Emergency Service Which are Certified IICRC Water damage and mold remediation contractors.
While it is a common problem, wet basements are something that most homeowners do not have to deal with if they take some precautions and the time to make some adjustments on their own. Many wet basement issues can be fixed by the homeowner without having to hire any outside help.
You can fix any cracks in the concrete walls of your basement where water is leaking in by using a simple injection of concrete. Doing this used to require expensive and heavy equipment, but the size and expense of this has gone down so significantly that you can now do it with a normal caulking gun. Do not try do this with the silicone caulking that you would use in a bathroom or kitchen or attempt to fix it with cement, either. These two items will only become loose and fall out, no longer forming the water barrier that you need to have in place.
If water is forming in puddles around the foundation of your house, then you probably need to pile some more soil around the house so the water runs away from the house instead of leaking down into the basement. Installing a drainage system can also help with this. Making sure your rain gutters stay cleaned out is also another thing that you can do to try and keep water out of your basement. While they seem unrelated, gutters that are clogged let water merely fall off the roof and down to the base of the house.
You can also choose to install a dehumidifier and some energy efficient windows. You will know that you have a humidity problem in the room if condensation builds up on the window panes. Putting in an exhaust vent down there can also help reduce the humidity, especially if you use the area as a laundry room or an extra bathroom. This helps prevent the steam from being absorbed by the rafters or the drywall ceiling.
Dror Klar is a writer and promoter of
Flushing, Kew Gardens, Maspeth Water Removal
and
Elizabeth NJ Wet Basement Flooding Emergency Service Which are Certified IICRC Water damage and mold remediation contractors.
Invisible Molds
Looking around for mold growth in your home is a burden that no one wants to have to take on, but sometimes not looking for it can cost you thousands of dollars in renovations later on after the growth has gotten so bad that the affected areas have to be completely gutted. Knowing how to spot mold early on is the key to saving all of this time and money, but it is not always as visible as some pictures on the internet and the news may have you believe. While mold does come in a variety of colorful species, it is not always as colorful as most of the images you come across.
Some molds are nigh invisible and grow on a few different surfaces mostly undetected unless you know how you need to look for them. Wood paneling, for example, can have mold growing on it and you not even realize it without the use of a simple bright flashlight. To be able to see the mold, however, you will need to know how to use the flashlight correctly. Instead of shining the light directly toward the paneling, you need to shine it along the surface of the paneling at an angle, so as to give the possible mold growth some depth. Only in this way will you be able to detect the extremely light colored molds growing on the different surfaces of your home. These molds tend to be a species in the Aspergillus or Penicillium genus.
Wood paneling is common in older homes and in homes that have been flood damaged, since replacing the affected drywall is a lot more expensive than simply installing paneling in its place. This is one reason mold likes to grow on this paneling: it is typically old and should be replaced.
You can miss these molds easily when you do a casual inspection of your home, but just taking a flashlight with you and knowing how to use it can save you a lot of money in the end. Molds that are not visible to you readily are not necessarily harmless; they can be just as detrimental to the building structure and your health as the molds that you do have the ability to see with the naked eye. Mold is not always an invisible threat, but it certainly can be, even if you think you know how to look for it.
Dror Klar is a writer and promoter of
Manhattan Water Damage Repair
and
Elizabeth, Newark, Trenton, Sayreville NJ Wet Basement Which are Certified IICRC Water damage and mold remediation contractors.
Some molds are nigh invisible and grow on a few different surfaces mostly undetected unless you know how you need to look for them. Wood paneling, for example, can have mold growing on it and you not even realize it without the use of a simple bright flashlight. To be able to see the mold, however, you will need to know how to use the flashlight correctly. Instead of shining the light directly toward the paneling, you need to shine it along the surface of the paneling at an angle, so as to give the possible mold growth some depth. Only in this way will you be able to detect the extremely light colored molds growing on the different surfaces of your home. These molds tend to be a species in the Aspergillus or Penicillium genus.
Wood paneling is common in older homes and in homes that have been flood damaged, since replacing the affected drywall is a lot more expensive than simply installing paneling in its place. This is one reason mold likes to grow on this paneling: it is typically old and should be replaced.
You can miss these molds easily when you do a casual inspection of your home, but just taking a flashlight with you and knowing how to use it can save you a lot of money in the end. Molds that are not visible to you readily are not necessarily harmless; they can be just as detrimental to the building structure and your health as the molds that you do have the ability to see with the naked eye. Mold is not always an invisible threat, but it certainly can be, even if you think you know how to look for it.
Dror Klar is a writer and promoter of
Manhattan Water Damage Repair
and
Elizabeth, Newark, Trenton, Sayreville NJ Wet Basement Which are Certified IICRC Water damage and mold remediation contractors.
Subscribe to:
Posts (Atom)
